ZXY EI41 Audio Transformer Low Frequency Silicon Steel Core Power Transformer
ZXY-14 Audio Isolation Transformer (marked “ZXY-14 AUDIO”), a compact audio coupling transformer built on a high-permeability laminated core and supplied as a dual matched pair for stereo and differential audio channels. Each unit measures 18 × 14 × 25 mm overall and is fitted with 75 mm flexible pure-copper lead wires, colour-coded Red for one winding and Blue for the other. A dot marking identifies the start point of each winding, so polarity can be confirmed at a glance du
Phone:13554723725
Email:rhea@zxycoil.com
Description
Application Specifications
ZXY-14 Audio Isolation Transformer (marked “ZXY-14 AUDIO”), a compact audio coupling transformer built on a high-permeability laminated core and supplied as a dual matched pair for stereo and differential audio channels. Each unit measures 18 × 14 × 25 mm overall and is fitted with 75 mm flexible pure-copper lead wires, colour-coded Red for one winding and Blue for the other. A dot marking identifies the start point of each winding, so polarity can be confirmed at a glance during assembly. The part is intended for professional audio use, where clean signal transfer, low distortion and reliable galvanic isolation are required.
· Compact size: 18 × 14 × 25 mm overall, with a 12 mm coil body - small enough for dense layouts.
· Dual matched pair: two transformers per set, produced and inspected so that both channels perform identically.
· Colour-coded leads: Primary = Red-Red, Secondary = Blue-Blue; each lead is 75 mm long with tinned stranded ends.
· Polarity reference: a dot marking on the winding identifies the start point of each coil.
· Laminated core: high-permeability laminated core for wide-band, low-loss signal transfer.
· Multi-layer winding: precision multi-layer winding for repeatable electrical performance and low distortion.
· Declared inductance: 906 mH ± 15 % (Red-Red) and 105.5 H ± 15 % (Blue-Blue), both measured at 100 Hz.
· DC resistance: 18.3 Ω ± 10 % (Red-Red) and 925 Ω ± 10 % (Blue-Blue).
· Dielectric strength: 500 Vrms / 5 mA for 1 second - PASS.
| Industry / Category | Target Application / Device | Key Function & Benefit |
| Home Appliances | Refrigerators,Air Conditioners,Washing Machines | Isolated-low-voltage control for mainboards, microcontrollers, |
| Audio & Consumer Electronics | Audio-Amplifiers,Power Adapters | Delivers clean, |
| HVAC & Climate Control | Thermostats,Boiler Controls | 110V/220V to standard 24V/12V AC |
| Industrial Automation | PLC Units, Instruments, Relays, Small Motors | stable auxiliary power supply |
| Security & Access Control | Alarm Systems, Intercoms, Door Lock Controllers | Guarantees continuous 24/7 low-voltage power |
Product Features
● Pure Copper Coil ZXY-14 Transformer for Low Heat & High Stability Power Conversion● Customizable ZXY-14Low Frequency Transformer for Linear Power Supply & Control Equipment● Silicon Steel Core EI41 Transformer with Low Noise & Low Idle Power Consumption● Epoxy Sealed Option for Waterproof, Dustproof and Vibration Resistant Application

img-mvalln3f-b60146ce
Product Advantages
●The ZXY-14 is engineered for audio excellence. Its laminated core and precision multi-layer winding keep insertion loss low and distortion minimal, while the transformer provides true galvanic isolation between the two windings. This breaks ground loops, removes hum, buzz and DC offset from the signal path, and lets equipment at different ground potentials be connected without a noise penalty.· Noise-free signal path: galvanic isolation between windings removes ground-loop hum and interference.· Consistent performance: matched winding and core assembly give high consistency from unit to unit.· Audio quality: low distortion and stable response for microphone and line-level audio.· Inspected individually: 100 % full electrical inspection on every single unit before packing.· Insulation safety: strict HI-POT and insulation safety test at 500 Vrms / 5 mA / 1 s.· Matched pairs: both channels of a stereo or differential link are supplied as a matched pair.Compliance-ready: CCC certified, CE compliant, RoHS compliant and UL recognized component.
Application scenario

12-场景图

img-mvallecq-8347c42f

img-mvallvrn-57054546

img-mvallohj-d0717dc5
Application
Recording microphones
microphone signal coupling in studio and recording chains.
Audio preamp & mixer
input and output isolation in microphone preamplifiers and mixing consoles.
Audio interface & DI box
audio interfaces, DI boxes and instrument-level input stages.
Signal isolation & coupling
galvanic isolation and signal coupling between separate pieces of audio equipment.
Product Details Showcase

img-mvallxcy-1b985374

img-mvallq64-789b386e

img-mvalltjd-ff4d7dce
Quality & Testing Assurance

Insulation Resistance
Verified to maintain ≥100 MΩat 500V DC under standard operating environments.
Efficiency & Loss Control
Designed to achieve ≥90% efficiency at rated load with minimal core and copper losses.

Dielectric Withstand Test (Hi-Pot)
100% tested at 1500V AC @ 50Hz for 1 minute between primary and secondary windings to prevent electrical leakage and ensure operator safety.
Environmental & Safety Compliance
Manufactured with flame-retardant materials and high-grade copper wire to conform to international safety and environmental standards.

证书 拷贝

证书
Specifications
Specifications have not been provided for this model. Send your application requirements to request a confirmed specification sheet.
Only supplied parameters are shown. Please confirm any unlisted electrical performance, test conditions, tolerances and customization options with our engineers. The final specification sheet takes precedence.
Product Images & Drawings
View the available product images and drawings below. Click to open the original. Customized products are subject to the agreed specifications and drawings.

















Downloads
No specification sheet has been uploaded for this model yet. Use the inquiry form below to request parameters, dimension drawings or sample information.
Selection & Customization Requirements
To help confirm a suitable model and specification, please provide:
- Your equipment, application, operating environment and temperature range.
- As applicable: inductance, turns ratio or impedance, operating frequency, voltage, current and insulation requirements.
- Size limits, mounting method, pin spacing, and any existing drawings or reference samples.
- Sample quantity, estimated order volume and desired delivery date.
Frequently Asked Questions
Common procurement questions about ZXY EI41 Audio Transformer Low Frequency Silicon Steel Core Power Transformer.
What is ZXY EI41 Audio Transformer Low Frequency Silicon Steel Core Power Transformer?
ZXY-14 Audio Isolation Transformer (marked “ZXY-14 AUDIO”), a compact audio coupling transformer built on a high-permeability laminated core and supplied as a dual matched pair for stereo and differential audio channels. Each unit measures 18 × 14 × 25 mm overall and is fitted with 75 mm flexible pure-copper lead wires, colour-coded Red for one winding and Blue for the other. A dot marking identifies the start point of each winding, so polarity can be confirmed at a glance du
Can ZXY EI41 Audio Transformer Low Frequency Silicon Steel Core Power Transformer be customized to our specifications?
Yes. Shenzhen ZhiXiangyuan Electronics Co., Ltd. provides OEM/ODM services. Inductance, turns ratio, current rating, core material, size and terminal style can all be customized according to your drawings or samples.
What is the MOQ and lead time for ZXY EI41 Audio Transformer Low Frequency Silicon Steel Core Power Transformer?
MOQ is negotiable based on the specific model and order quantity. Typical lead time is 1-3 weeks for standard items and 2-4 weeks for customized orders. Contact our sales team for an exact quotation.
Do you provide samples of ZXY EI41 Audio Transformer Low Frequency Silicon Steel Core Power Transformer?
Yes, samples are available for evaluation before bulk orders. Please send us your requirements and shipping details to request samples.
What is the model number of this product?
The model number is EI41. Custom model numbers can be assigned for OEM orders.
Send Us a Message
Tell us your requirements and our engineers will reply within 24 hours.






