Click the main image to view the original. Select a thumbnail to switch.1 / 17
ZXY-EI25 Flying Lead Audio Isolation Transformer, 1:4 Turns Ratio, 50 Hz-20 kHz, EI25 Laminated Core
ZXY-EI25, a flying-lead audio isolation transformer built on an EI25 laminated core. Its two windings are isolated and wound to a 1:4 turns ratio. At 1 kHz and 0.3 V the primary measures 56 mH min and the secondary 800 mH min; DC resistance at 25 °C is 1.6 Ω on the primary and 17 Ω on the secondary, ±15 %. The part covers 50 Hz to 20 kHz and is designed for low distortion across that band, which is why it is described as both a voice and a data coupling transformer.
- 耐压测试
- 1,500 V, 1 mA, 60 s
- 耐压测试（2）
- 1,500 V, 1 mA, 60 s
- 频率范围
- 50 Hz 至 20 kHz
Phone:13554723725
Email:rhea@zxycoil.com
Description
1. Product Name
ZXY-EI25, a flying-lead audio isolation transformer built on an EI25 laminated core. Its two windings are isolated and wound to a 1:4 turns ratio. At 1 kHz and 0.3 V the primary measures 56 mH min and the secondary 800 mH min; DC resistance at 25 °C is 1.6 Ω on the primary and 17 Ω on the secondary, ±15 %. The part covers 50 Hz to 20 kHz and is designed for low distortion across that band, which is why it is described as both a voice and a data coupling transformer.
Two windings, one barrier. The windings are separated, so the signal crosses while the ground path between the two pieces of equipment does not. That is the whole point of the part: it removes the AC hum that system grounding puts on a signal line, and it keeps a fault on one side away from the output stage on the other. Polarity is marked on both windings and defined by the schematic reproduced in the next section.
2. Construction & Materials
The core. An EI25 laminated core, which is the core the specification names. The inductance figures quoted on this page, 56 mH min on the primary and 800 mH min on the secondary, are measured with it at 1 kHz and 0.3 V, and they are the numbers to check a delivered part against.
The windings and their polarity. Two isolated windings, 1:4. The specification defines polarity by the approved schematic, and the schematic supplied with this product is reproduced below: each winding carries a polarity dot at the same end of the symbol, and the two windings sit either side of the insulation barrier. The source does not assign lead colours to windings, so take the winding-to-colour mapping from the schematic that ships with the order rather than from a photograph.
The termination. Flying leads with tinned ends, so the part is wired into a harness or a terminal block instead of being reflowed onto a land pattern. Tinned ends are solderable as supplied, without stripping and re-tinning on the bench, and the lead length gives the routing freedom that a pinned part does not have. Lead length and wire gauge are not declared in the source and are therefore not quoted on this page.
3. Feature
Flying-lead build on an EI25 laminated core. The part is wired in through leads rather than a land pattern, so the mounting position is set by the harness and not by a PCB footprint.
Turns ratio 1:4. The secondary carries four times the turns of the primary, and the two windings are isolated from each other.
Inductance 56 mH min and 800 mH min at 1 kHz / 0.3 V. Primary and secondary respectively, verified on both windings at the stated condition.
DCR 1.6 Ω and 17 Ω at 25 °C, ±15 %. Primary and secondary respectively; the tolerance is declared, so a delivered part can be checked against a limit rather than against a nominal.
Hi-pot 1,500 V, 1 mA, 60 s. A dielectric test at a declared voltage, a declared leakage limit and a declared duration.
Frequency range 50 Hz to 20 kHz. Voice and programme material in one band, which is why the part is described as both a voice and a data coupling transformer.
Two isolated windings with polarity marking. Polarity is defined by the approved schematic, so phase can be held between units in a build.
Flying leads with tinned ends. Solderable as supplied, without a strip-and-re-tin operation on the bench.
Low distortion across a wide frequency response. Speech clarity and audio fidelity from one part, as the source puts it.
Body 26.0 × 19.0 mm, height 14.8 mm. Per the outline drawing: compact enough to sit inside an audio module or behind a connector panel.
4. Advantage
The signal crosses, the ground does not. The isolated 1:4 windings transfer the signal while breaking the ground path between the two pieces of equipment, which is the barrier doing the work rather than a filter.
Ground-loop hum removed at the cause. AC hum produced by system grounding is stopped by the barrier instead of being trimmed out downstream.
Front-end output stages protected. A fault on one side does not reach the output stage of the equipment on the other, which is what the source means by protecting against burnout.
Balanced and unbalanced lines both covered. External interference on either kind of transmission line is reduced by the same barrier.
Installed by lead, not by footprint. The flying leads fit multiple wiring scenarios, which is the practical advantage over a pinned part when the harness is already designed.
One part for voice and data. A single 50 Hz to 20 kHz transformer covers the coupling job in both, so the bill of materials does not need two parts.
Customized designs to requirement. Alternative windings are available on request; the series build is the 1:4 part described here.
5. Application
Professional audio. Lavalier, camera and instrument microphones, mic preamps and audio isolation modules.
Audio systems. High-end speakers, home theatre and car audio, for signal isolation and noise elimination.
Communication equipment. Telephones, fax machines, IP voice terminals and modems, for signal coupling.
Industrial and broadcast systems. Public address and conference systems, for audio isolation and transmission.
6. Specifications
The tables below reproduce the specification as declared for ZXY-EI25, given in the source as the ZXYEI25 flying-lead version. Where the source gives no figure, the cell says so instead of carrying a number in from another series.
6.1 Summary
| Item | Specification | Note |
|---|---|---|
| Model | ZXY-EI25 flying lead | ZXYEI25 flying-lead version |
| Reference part number | B2316 | Reference the source gives; confirm on order |
| Core | EI25 laminated core | Declared as laminated |
| Turns ratio | 1:4 | Two isolated windings |
| Inductance | 56 mH min / 800 mH min | Primary / secondary, at 1 kHz and 0.3 V |
| DCR at 25 °C | 1.6 Ω / 17 Ω | ±15 %, primary / secondary |
| Hi-pot | 1,500 V, 1 mA, 60 s | AC or DC not declared |
| Frequency range | 50 Hz to 20 kHz | Low-distortion design intent |
| Windings | Two isolated windings | Polarity marked per schematic |
| Termination | Flying leads with tinned ends | Lead length and gauge not declared |
| Body | 26.0 × 19.0 mm, height 14.8 mm | Per the outline drawing |
| Options | Customized design | Alternative windings on request |
6.2 Electrical
| Parameter | Specification | Test condition |
|---|---|---|
| Turns ratio | 1:4 | Primary to secondary |
| Inductance, primary | 56 mH minimum | At 1 kHz and 0.3 V |
| Inductance, secondary | 800 mH minimum | At 1 kHz and 0.3 V |
| DC resistance, primary | 1.6 Ω ±15 % | At 25 °C |
| DC resistance, secondary | 17 Ω ±15 % | At 25 °C |
| Hi-pot | 1,500 V at 1 mA | For 60 s; AC or DC not declared |
| Frequency range | 50 Hz to 20 kHz | No tolerance in dB declared |
| Isolation | Two isolated windings | Ground path broken between equipment |
6.3 Materials and construction
| Item | Specification | Declared property |
|---|---|---|
| Core | EI25 laminated core | Laminated, as declared |
| Windings | Two isolated windings | 1:4 turns ratio, polarity marked |
| Termination | Flying leads, tinned ends | Tinned for direct soldering |
| Insulation class | Not declared | Request it with the drawing |
| Encapsulation | Not declared | Request it with the drawing |
6.4 Mechanical and termination
| Item | Value | Note |
|---|---|---|
| Body length | 26.0 mm | Per the outline drawing |
| Body width | 19.0 mm | Per the outline drawing |
| Body height | 14.8 mm | Per the outline drawing |
| Termination | Flying leads, four shown | Lead count is not stated in the source |
| Lead length and gauge | Not declared | Confirm on the drawing |
| Weight | Not declared | Confirm on the drawing |
| Mounting | Wired by flying leads | No land pattern is declared |
6.5 Quality and testing
| Item | Requirement | Condition |
|---|---|---|
| Hi-pot | 1,500 V, 1 mA, 60 s | Tested per unit |
| Inductance | 56 mH min / 800 mH min | Verified at 1 kHz / 0.3 V on both windings |
| DCR | 1.6 Ω / 17 Ω | ±15 %, at 25 °C |
| Polarity | Marked per schematic | Defined by the approved schematic |
| Electrical data source | EI25 product specification | Measured at 25 °C |
7. Ordering
The part is ordered as ZXY-EI25, described in the specification as the ZXYEI25 flying-lead version. The specification also lists a reference part number, B2316; it is quoted here as the reference the source gives, not as an independently verified ordering code, so confirm it against the ZXY order confirmation. Alternative windings and customized designs are available on request, and a customized build is quoted against a drawing or a sample rather than against this table.
Certification: no certificate naming ZXY-EI25 was supplied with this description, so no compliance claim is made on this page and the render that carries a row of certification badges was not used. If the listing needs a certificate, quote the number from the certificate itself.
Brand / manufacturer: ZXY, Shenzhen Zhixiangyuan Electronics Co., Ltd. http://www.zxycoil.com
Specifications
| 耐压测试 | 1,500 V, 1 mA, 60 s |
|---|---|
| 耐压测试（2） | 1,500 V, 1 mA, 60 s |
| 频率范围 | 50 Hz 至 20 kHz |
| 直流电阻 | 初级1.6 Ω，次级17 Ω，±15 % 在25 °C |
| 匝数比 | 1 |
| OEM/ODM | 定制设计和按需提供替代绕组 |
| 磁芯材料 | EI25叠片磁芯 |
| 型号 | ZXY-EI25 |
| 品牌名称 | ZXY |
| 产地 | 中国广东 |
| 电感量 | 初级56 mH min，次级800 mH min 在1 kHz / 0.3 V |
Only supplied parameters are shown. Please confirm any unlisted electrical performance, test conditions, tolerances and customization options with our engineers. The final specification sheet takes precedence.
Product Images & Drawings
View the available product images and drawings below. Click to open the original. Customized products are subject to the agreed specifications and drawings.
Downloads
No specification sheet has been uploaded for this model yet. Use the inquiry form below to request parameters, dimension drawings or sample information.
Selection & Customization Requirements
To help confirm a suitable model and specification, please provide:
- Your equipment, application, operating environment and temperature range.
- As applicable: inductance, turns ratio or impedance, operating frequency, voltage, current and insulation requirements.
- Size limits, mounting method, pin spacing, and any existing drawings or reference samples.
- Sample quantity, estimated order volume and desired delivery date.
Frequently Asked Questions
Common procurement questions about ZXY-EI25 Flying Lead Audio Isolation Transformer, 1:4 Turns Ratio, 50 Hz-20 kHz, EI25 Laminated Core.
What is ZXY-EI25 Flying Lead Audio Isolation Transformer, 1:4 Turns Ratio, 50 Hz-20 kHz, EI25 Laminated Core?
ZXY-EI25, a flying-lead audio isolation transformer built on an EI25 laminated core. Its two windings are isolated and wound to a 1:4 turns ratio. At 1 kHz and 0.3 V the primary measures 56 mH min and the secondary 800 mH min; DC resistance at 25 °C is 1.6 Ω on the primary and 17 Ω on the secondary, ±15 %. The part covers 50 Hz to 20 kHz and is designed for low distortion across that band, which is why it is described as both a voice and a data coupling transformer.
Can ZXY-EI25 Flying Lead Audio Isolation Transformer, 1:4 Turns Ratio, 50 Hz-20 kHz, EI25 Laminated Core be customized to our specifications?
Yes. Shenzhen ZhiXiangyuan Electronics Co., Ltd. provides OEM/ODM services. Inductance, turns ratio, current rating, core material, size and terminal style can all be customized according to your drawings or samples.
What is the MOQ and lead time for ZXY-EI25 Flying Lead Audio Isolation Transformer, 1:4 Turns Ratio, 50 Hz-20 kHz, EI25 Laminated Core?
MOQ is negotiable based on the specific model and order quantity. Typical lead time is 1-3 weeks for standard items and 2-4 weeks for customized orders. Contact our sales team for an exact quotation.
Do you provide samples of ZXY-EI25 Flying Lead Audio Isolation Transformer, 1:4 Turns Ratio, 50 Hz-20 kHz, EI25 Laminated Core?
Yes, samples are available for evaluation before bulk orders. Please send us your requirements and shipping details to request samples.
What is the model number of this product?
The model number is ZXY-EI25. Custom model numbers can be assigned for OEM orders.
Send Us a Message
Tell us your requirements and our engineers will reply within 24 hours.
